Back to Blog
How-to Guides 2026-11-20 Tala | Shop Official Tala® Lighting | Light to Live By – Tala US 0 views

How to Replace the Battery in a Mantle Portable Lamp

How to Replace the Battery in a Mantle Portable Lamp

Step-by-step guide to replacing the battery in a Tala Mantle Portable Lamp, including when to swap the PCB and what parts you need.

When to Replace the Battery in Your Mantle Portable Lamp

If your Mantle Portable Lamp no longer holds a charge or turns off sooner than it used to, the battery may need replacing. Tala offers a dedicated Mantle Replacement Battery - Set of 2 (SKU: ACC-MTL-BTY-01) designed specifically for this lamp. The set includes two batteries, so you can keep one spare on hand.

Before you order, check whether the lamp's printed circuit board (PCB) is also damaged. If the lamp does not respond even with a fresh battery, the Mantle Replacement PCB (ACC-MTL-PCB-01) might be the issue.

Mantle Replacement PCB
Mantle Replacement PCB

Compatible Replacement Parts

  • Mantle Replacement Battery - Set of 2: Set of 2 replacement batteries designed for the Mantle Portable Lamp. SKU: ACC-MTL-BTY-01. This is the exact battery pack for your Mantle lamp, giving you a spare for future swaps.
    Mantle Replacement Battery - Set of 2
    Mantle Replacement Battery - Set of 2
  • Mantle Replacement PCB - RT: The Mantle Replacement PCB is a replacement printed circuit board for the Mantle Portable Lamp, offered as a Standard option under code ACC-MTL-PCB-01. If the lamp still doesn't power on after a battery change, the PCB may need replacing. This part is compatible with the same lamp model.

How to Replace the Battery in a Mantle Portable Lamp

Replacing the battery is a straightforward process. The following steps are based on the general design of portable lamps; always check your lamp for specific instructions.

  1. 1. Turn off and disconnect the lamp: Make sure the lamp is switched off and not connected to any power source. Remove any charging cable if attached.
  2. 2. Access the battery compartment: Locate the battery compartment on the Mantle Portable Lamp. It is typically accessible from the base or underside. Use a suitable tool if needed to open the cover.
  3. 3. Remove the old battery: Carefully disconnect the old battery from its connector. Note the orientation and connector type so you can insert the new one correctly.
  4. 4. Insert the new battery: Take one of the Mantle Replacement Batteries and connect it to the same port. Ensure the connection is secure and the battery sits flat inside the compartment.
  5. 5. Close the compartment and test: Replace the cover and turn on the lamp. If it lights up normally, the replacement is successful. If not, the PCB may need attention.

When to Replace the Mantle PCB Instead

If the lamp still does not work after a fresh battery, the printed circuit board may be faulty. The Mantle Replacement PCB is a drop-in replacement for the original board.

  1. 1. Confirm the lamp is off and disconnected: Same as the battery swap: power off and unplug any charger.
  2. 2. Open the lamp housing: Access the internal electronics. This may require removing additional screws or panels. Proceed with care.
  3. 3. Disconnect the old PCB: Unplug any connectors attached to the board. Note where each cable goes.
  4. 4. Install the new PCB: Insert the Mantle Replacement PCB (ACC-MTL-PCB-01) and reconnect all cables in the same positions. Ensure the board is seated properly.
  5. 5. Reassemble and test: Close the housing, install a charged battery, and turn on the lamp. If it works, the PCB was the issue.

What to Do If the Lamp Still Doesn't Work

If replacing both the battery and the PCB does not resolve the issue, the problem may lie elsewhere in the lamp's circuitry or wiring. In that case, contact Tala support or a qualified technician. The records do not cover further repair steps, so avoid attempting internal repairs beyond what is described here.

Related Articles

Customer Service
Home
Products
Cart
Profile